江苏盘扣式脚手架生产厂家

产品介绍 Product introduction
1.产品概述  Product overview
盘扣式多功能脚手架，是继碗扣式脚手架之后升级换代产品。这种脚手架立杆采用直径60mm、直径48mm，壁厚3.2mm、Q355B钢管做主构件，圆盘为直径135mm、122mm厚10mm的圆盘，圆盘上开设8个孔，设有水平杆、斜杆连接孔。
Dish buckle type multi-functional scaffolding, is after the bowl buckle type scaffolding upgrade products. This kind of scaffold pole adopts the diameter of 60mm, the diameter of 48mm, the wall thickness of 3.2mm, Q355B steel pipe as the main component, the disk is the diameter of 135mm, 122mm thick 10mm disk, the disk is provided with 8 holes, with horizontal bar, oblique bar connection hole.


2.主要构件（立杆，水平杆，竖向斜杆，图片，型号）
. Main components (vertical, horizontal, diagonal, picture, model)
◆立杆 Vertical pole
•标准化圆盘式节点设计
•采用Q355B低碳合金结构钢
•1.5m步距单根极限荷载可达17吨
•全自动的专业焊接工艺
•热镀锌浸镀工艺
    • Standardized disk joint design            
•Adopt Q355B low carbon alloy structural steel            
•1.5m step distance single ultimate load up to 17 tons            
•Full automatic professional welding process            
• Hot dip galvanizing process

◆水平杆  Horizontal bar
•标准化自锁式插销设计
•国际标准的铸钢连接件
•全自动的专业焊接工艺
•热镀锌浸镀工艺
• standardized self-locking pin design            
•International standard steel connectors            
•Full automatic professional welding process            
• hot dip galvanizing process

◆竖向斜杆  vertical diagonal bar
•标准化斜杆，为设计搭建稳定的系统结构提供必要条件
•标准化自锁式插销
•国际标准的铸钢连接件
•热镀锌浸镀工艺

      •Standardized diagonal bars provide necessary conditions for the design and construction of stable system structure            
• standardized self-locking pins            
•International standard steel connectors            
• hot dip galvanizing process

◆可调上下托撑  Adjustable upper and lower bracket
•JGJ231-2010*6.1.5条强制性规定：
模板支架可调托座伸出**层或双槽钢托梁的悬臂长度严禁**过650mm，且丝杆外露长度严禁**过400mm，可调托座插入立杆或双槽钢托梁长度不得小于150mm’。
•JGJ231-2010*6.1.7条规定：
模板支架可调底座丝杆外露长度不应大于300mm，作为扫地杆的较底层水平杆离地高度不应大于550mm。
   •article 6.1.5 of jgj231-2010 is mandatory:            
The cantilever length of adjustable bracket of formwork support extending out of the top layer or double channel steel joist shall not exceed 650mm, and the exposed length of screw rod shall not exceed 400mm, and the length of adjustable bracket inserted into upright or double channel steel joist shall not be less than 150 mm '.       
•article 6.1.7 of jgj231-2010 stipulates:              
The exposed length of the screw rod of the adjustable base of the formwork support shall not be greater than 300 mm, and the height from the ground of the lowest level horizontal rod as the bottom of the sweeping rod shall not be greater than 550 mm.


◆爬梯 Ladder  
•用于搭设上下通道。表面 镀锌处理，防火、美观， 防滑，采用挂钩式连接， 拼装快捷
•规格 ：（单位mm）
•720×2100×2000
•720×1800×2000

• it is used to set up upper and lower channels. Galvanized surface, fire-proof, beautiful, anti-skid, hook type connection, quick assembly 
•specification: (unit: mm) 
• 720 × 2100 × 2000 
• 720 × 1800 × 2000

◆钢踏板  Steel pedal
•两端依靠挂钩挂在水平横杆上，用于搭设施工操作平台
•1.5mm厚带钢一次滚压成型，表面热镀锌处理
•规格同水平横杆
•The two ends are attached to the horizontal cross bar by the hook, which is used to set up the construction operation platform. 
•The 1.5mm thick steel strip is rolled once, and the surface is hot-dip galvanized. 
•The specification is the same as the horizontal cross bar