产品规格: | 不限 | 产品数量: | 不限 |
---|---|---|---|
包装说明: | 按订单 | 价格说明: | 不限 |
查看人数: | 9 人 | 本页链接: | https://info.b2b168.com/s168-138810637.html |
混流泵是一种“拉出”式结构泵,在检查和拆卸叶轮和轴封时,雨水混流泵厂家,毋须将与泵体相连接的管路拆开。装有精密加工的泵轴,装有稀油润滑的轴承,在填料函盖中装有防护轴套。轴承箱的油位,可由恒位油杯来控制。
泵体的支脚,可承受来自管路的任何载荷,并直接传递给基础。这样,转子不会因为泵承受泵受载荷而产生弯曲,从而保证轴承的使用寿命。
由于较大的过流面积,从而减少阻塞。
泵的旋转方向,从驱动端看,雨水混流泵销售,为顺时针方向。
动力驱动可采用电动机或内燃机。
泵装置上可以配备完整的放气装置,有利于吸入管路的排气。
混流泵,英文为:Mixed flow pump
当原动机带动叶轮旋转后,对液体的作用既有离心力又有轴向推力,是离心泵和轴流泵的综合,液体斜向流出叶轮。因此它是介于离心泵和轴流泵之间的一种泵。混流泵的比转速**离心泵,低于轴流泵,一般在300-500之间。它的扬程比轴流泵高,但流量比轴流泵小,比离心泵大。3应用范围编辑用于输送清洁和污染的介质,化学中性或侵蚀性的介质。
化工流程中强制循环、海水养殖、城市煤气工程、水处理系统。
开车顺序:
1、关闭出口闸阀
2、将水注入水泵,以排除进水管及泵内空气,可从泵体*引水杯注入清水,也可用真空泵注水(开动真空泵,排除水泵及管内气体在水充满水泵的同时,起动水泵,打开闸阀,停止真空泵)。
3、开启电动机(注意水泵的旋转方向)。
4、当电动机正常运转后,逐步开大闸阀,达到所要求的工况后,调节填料松紧。若水泵运转,轴承温度等都正常,则可继续运行。
III. Starting
Sequence
1.Close the oulet
sluice valve.
2. Inject
water into pump to remove the air in water-in pipe and pump which can realized
by injecting clear water from the water diversion cup of the pump body end or
by vacuum pump(start the vacuum pump, remove the air from pump and pipes, start
the water pump when the pump is full of water,漯河雨水混流泵, open the sluice valve, stop the
vacuum pump).
3. Start the
motor(pay more attention on the rotation direction of pump)
4. When the motor runs normally, turn up the
sluice valve gradually, adjust the tightness of padding when gettng to the
required working condition.If the pump runs well, the temperature of bearing is
normal, and it can run sequentially.